Product Overview

The Pentair Clean & Clear Plus Tank Lid Assembly | 170024 is a genuine OEM replacement upper tank lid designed for specific Pentair cartridge and D.E. filter models.

This replacement lid is made for the Pentair Clean & Clear Plus 320-square-foot cartridge filter and the Pentair Quad D.E. 60-square-foot filter. It replaces a filter lid that has become cracked, warped, damaged, or unable to maintain a proper seal.

Because pool filters operate under pressure, a damaged tank lid should never be patched, modified, or placed back into service. Replacing it with the correct genuine Pentair component helps restore proper filter-tank alignment, sealing, and safe system operation.

This part is model-specific and does not fit every Clean & Clear Plus or Quad D.E. filter size.

Key Features

• Genuine Pentair OEM replacement component
• Replacement upper filter-tank lid
• Fits the Clean & Clear Plus 320 cartridge filter
• Fits the Quad D.E. 60-square-foot filter
• Durable fiberglass-reinforced polymer construction
• Almond or tan factory finish
• Engineered to match the original tank dimensions
• Restores proper filter-tank closure and alignment
• Designed for pressurized pool-filtration systems
• Suitable for residential pool-equipment repairs
• Direct replacement for Pentair part number 170024

Benefits

• Replaces a cracked, warped, or damaged filter lid
• Restores the structural integrity of the filter tank
• Helps maintain proper internal operating pressure
• Provides OEM fitment for compatible filter models
• Helps prevent leaks caused by a compromised lid
• Allows continued use of the existing compatible filter body
• Avoids replacing the entire filter when only the lid is damaged
• Genuine Pentair construction provides dependable compatibility

Specifications

Compatible Filter Models

This tank lid is designed for the following Pentair filters:

• Pentair Clean & Clear Plus CCP320
• Pentair Clean & Clear Plus 320 sq. ft. cartridge filter
• Pentair Quad D.E. 60 sq. ft. filter
• Pentair Quad D.E. model 188592

Compatibility should always be confirmed using the filter model, tank label, serial information, and existing lid part number.

What Is Included

• One Pentair replacement upper tank lid assembly

Pressure gauges, air-relief assemblies, clamps, O-rings, cartridges, internal components, and other hardware should not be assumed to be included unless specifically shown or stated with the product at the time of purchase.

Inspect the existing filter components before installation and replace any worn or damaged sealing parts as required.

Installation Information

Pool filters operate under high pressure and can cause serious injury if opened or serviced improperly. Professional installation is strongly recommended.

Before removing the existing lid:

1. Turn off the pool pump at the breaker.
2. Prevent the pump from restarting during service.
3. Open the manual air-relief valve.
4. Confirm the pressure gauge reads zero.
5. Allow all trapped pressure to escape.
6. Remove the clamp only after the filter is completely depressurized.

Inspect the lower tank, clamp, O-ring, pressure gauge, air-relief assembly, and sealing surfaces before installing the replacement lid. Do not reuse a damaged clamp or deteriorated tank O-ring.

The lid and lower tank must be aligned correctly, and the clamp must be installed according to Pentair’s service instructions before restarting the system.

Confirm Before Ordering

• Confirm Pentair part number 170024.
• Verify the filter is a Clean & Clear Plus 320 or Quad D.E. 60.
• Do not order based only on the filter’s appearance.
• Check the model number on the filter tank label.
• Confirm the existing lid dimensions and part number.
• This part does not fit every Clean & Clear Plus filter size.
• This part does not fit every Quad D.E. filter size.
• Inspect the lower tank for cracks or structural damage.
• Inspect the tank clamp before reassembly.
• Determine whether a new tank O-ring is required.
• Confirm whether the pressure gauge and air-relief assembly must be transferred or replaced.
• Never repair or reuse a cracked pressurized filter lid.
• Have the filter professionally inspected and installed.

Warranty Information

This genuine Pentair replacement part is covered under Pentair’s applicable limited parts-warranty terms.

Warranty coverage may depend on purchase through an authorized dealer, correct model compatibility, professional installation, proper system operation, and compliance with Pentair’s installation and service instructions.

Damage caused by incorrect installation, excessive pressure, freeze damage, chemical misuse, incompatible equipment, improper clamp installation, unauthorized modification, or continued operation with a damaged tank may not be covered.

Keep the original purchase receipt and professional installation invoice for warranty purposes.

Customer Q&A

Does part 170024 fit every Clean & Clear Plus filter?
No. It is specifically associated with the Clean & Clear Plus 320-square-foot filter.

Does it fit a Quad D.E. filter?
Yes. It is also used with the Pentair Quad D.E. 60-square-foot filter.

Will it fit the CCP420 or CCP520?
No. Those filter sizes use different upper tank components. Confirm the exact filter model before ordering.

Is this a genuine Pentair part?
Yes. Part number 170024 is a genuine Pentair replacement tank lid.

What color is the lid?
The lid is generally supplied in Pentair’s almond or tan finish.

Does it include the lower tank?
No. This listing is for the upper tank lid assembly only.

Does it include the tank clamp and O-ring?
Do not assume these components are included. Review the product contents and replace worn sealing or clamping components separately when necessary.

Can a cracked filter lid be repaired?
No. A damaged pressure-vessel component should be removed from service and replaced with the correct part.

Should a professional install the lid?
Yes. Filter tanks operate under pressure, and professional inspection and installation are strongly recommended.